- Remove net-mgmt/bsnmpd, is part of base since FreeBSD 6.0

Conversion from (now defunct) autoconf-2.61 to autoconf-2.62

Tested by:      exp build run (erwin)

- Remove USE_GCC where it can be satisfied with base compiler on following
  FreeBSD versions: 5.3 and up, 6.x, 7.x, 8-CURRENT

- Remove unneeded dependency from gtk12/gtk20 [1]
- Remove USE_XLIB/USE_X_PREFIX/USE_XPM in favor of USE_XORG
- Remove X11BASE support in favor of LOCALBASE or PREFIX
- Use USE_LDCONFIG instead of INSTALLS_SHLIB
- Remove unneeded USE_GCC 3.4+

Thanks to all Helpers:
        Dmitry Marakasov, Chess Griffin, beech@, dinoex, rafan, gahr,
        ehaupt, nox, itetcu, flz, pav

PR:             116263
Tested on:      pointyhat
Approved by:    portmgr (pav)

Switch autoconf dependencies from 2.53 or 2.59 to 2.61.

PR:             ports/116639
Submitted by:   aDe

Update to 1.12

PR:             96285
Submitted by:   "Andrey V. Elsukov" <bu7cher@yandex.ru> (maintainer)

SHA256ify

Approved by: krion@

Fix build on 5.x

PR:             92192
Submitted by:   <bu7cher@yandex.ru> (maintainer)

Now that new style rc.d scripts are being run as part of the
base rcorder, hard coded variable values in these scripts
are overriding the values in /etc/rc.conf[.local] (due to
the way that variables from the latter are read at boot time).

Therefore, change the boot scripts to set default values only
if the variable is unset in /etc/rc.conf[.local]. This will
allow the service to start at boot time if it's been enabled
as the user would expect.

This change will be a noop for users who have systems that
have not yet been upgraded to the new rc.d code in the base.

In many cases there are other variables in the scripts that
should get similar treatment, however I did not change
anything other than the _enable lines. I'll leave the rest
up to the maintainers to do as they see fit.

Bump PORTREVISION to make sure that users and packages
pick up this change.

Switch to <target>:: convention for both patch-autotools and run-autotools,
to allow for easier overriding of these targets by port Makefiles, if
they need to.

Mass-conversion to the USE_AUTOTOOLS New World Order.  The code present
in bsd.autotools.mk essentially makes this a no-op given that all the
old variables set a USE_AUTOTOOLS_COMPAT variable, which is parsed in
exactly the same way as USE_AUTOTOOLS itself.

Moreover, USE_AUTOTOOLS has already been extensively tested by the GNOME
team -- all GNOME 2.12.x ports use it.

Preliminary documentation can be found at:
        http://people.FreeBSD.org/~ade/autotools.txt

which is in the process of being SGMLized before introduction into the
Porters Handbook.

Light blue touch-paper.  Run.

Update to 1.11a

PR:             87039
Submitted by:   Andrey V. Elsukov <bu7cher@yandex.ru> (maintainer)

- Update to 1.11

PR:             ports/86945
Submitted by:   maintainer

- Fix build on 5.x

PR:             ports/86696
Submitted by:   maintainer
Reported by:    pointyhat

Fix build

Notified by:    kris
Approved by:    pav (mentor)

New port

This is a mini-SNMP daemon. The basic daemon implements the system group
and a number of private extensions to manage the UDP transport mapping,
communities, trap destinations and loadable modules. In this form it can
be used to provide remote access to arbitrary data that can be described in
the form as required by the SMI. The daemon speaks both SNMPv1 and SNMPv2c.

PR:             86400
Submitted by:   Andrey V. Elsukov <bu7cher@yandex.ru>
Approved by:    pav (mentor)